Which steps must be done daily before using a forklift?

OSHA requires that all forklifts be examined at least daily before they are used to ensure that they’re in safe operating condition. If forklifts are used on a round-the-clock basis, then they must be examined after each shift.

Which steps should you do every time you park a forklift?

Parking Safety Rules

  • Always try to find a level surface to park on. …
  • Lower forks, or the forklift attachment, all the way to the ground. …
  • Put the gear into neutral.
  • Make sure the wheels are straight. …
  • Set the parking brake every time you park the forklift. …
  • Turn off the engine before dismounting the forklift.

What are the three safety inspection steps you must take before operating a forklift?

The Pre-Operation Inspection

  • Fluid levels, including the oil, water, and hydraulic fluid.
  • Leaks, cracks, or any other visible defect including hydraulic hoses and mast chains.
  • Tire pressure and condition.
  • Load backrest extension.
  • Finger guards.
  • Safety decals and nameplates.
  • Operator manual.
  • Operator compartment.
IT IS INTERESTING:  What is the fulcrum point on a forklift?

When parking or leaving the forklift you must remove the ignition key?

When parking a forklift, slowly bring the vehicle to a stop, set the parking brake, turn off the ignition and remove the keys. If you are parking on an incline, turn the front wheels away from the downgrade so the forklift will not slide.

Is it illegal to leave keys in a forklift?

You might not be aware but it is actually illegal to leave the keys in an unattended Forklift. This measure is to prevent unauthorised use of the Forklift. … All forklifts and plant equipment can be fitted with low cost Driver Identification systems which prevent unauthorised usage.

What is the correct way to drive a forklift?

To reduce these hazards, follow these requirements and recommendations:

  1. Always drive unloaded forklifts with the forks downgrade.
  2. Never drive a loaded forklift with the load downgrade.
  3. When driving up a ramp, drive loaded forklifts forward with the load upgrade.

What are 3 fluid levels that need to be checked before using the forklift?

Check of liquid Levels:

  • Hydraulic fluid.
  • Brake fluid.
  • Engine oil coolant.
  • Battery.
  • Fuel.

Is forklift driving hard?

Driving a forklift isn’t all cake, roses, and gas pedals. It’s going to be hard work. … Operating a forklift is considered a “hazardous occupation,” according to the Fair Labor Standards Act. As with any big machine, accidents happen.

What is the first thing you do before operating a forklift?

The first step toward safe forklift operation is conducting the preoperational inspection. Forklift operators should conduct the inspection at the start of each work shift to ensure that the forklift will work properly. According to OSHA, 1 in 15 forklift-related accidents are caused by improper maintenance.

IT IS INTERESTING:  Why should a lift truck not be turned on a ramp?

When should a forklift be taken out of service?

In today’s article, we look at some of the scenarios where it is ideal to take your forklift out of service.

  1. Overheating Engine. When the engine of a heavy machine like the forklift malfunctions then there is cause for concern. …
  2. Noticeable Defects. …
  3. Leaking Fuel. …
  4. Exhaust Sparks. …
  5. Recent Accidents.

When picking up a load the forks should be?

Answer Expert Verified. Answer: When picking up a load the correct fork spacing should be 6 inches and also the forks must be spaced as wide apart as necessary for the maximum support of the load.

What are the four main causes of forklift injuries?

4 Common Causes of Forklift Operator Injury or Death

  • Lift trucks are inadvertently driven off loading docks.
  • Lifts fall between docks and an unsecured trailer while a worker in onboard.
  • Workers (or pedestrians) can be struck by a lift truck.
  • Trucks may fall while on elevated pallets and tines.
Blog about special equipment